AddPac VoiceFinder AP1100 Guía de usuario Pagina 137
- Pagina / 302
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
VoiceFinder AP1100 VoIP Gateway User’s Guide Version 1.1
AddPac Technology Co., Ltd. -
137 -
5.3.2.4. Setting CODEC and VAD in the Dial Peer
To set the COder-DECoder(CODEC) and the Voice Activity Detection (VAD) in
the dial peer, how much bandwidth the voice session can have shall be
defined. Normally, the CODEC converts analog signals into digital bit streams
or vice versa. During this procedure, the CODEC defines the voice coder rate
for the dial peer. The VAD prohibits silent packets (created while the
caller/callee does not talk) from being sent.
5.3.2.4.1. Setting CODEC in the VoIP Dial Peer
To set the coder rate for the selected VoIP peer, use the following commands
in the global setup mode (start.)
Step Command Description
1 dial-peer voice
tag
VoIP
Enters into the dial-peer setup mode to set the
VoIP peer.
2 codec [g711alaw / g711ulaw
/g729 / g7231r63 /g7231r53]
Selects the CODEC for the voice considering the
coder rate.
Codec The default of “Codec” command is g7231r63. In normal cases, the
default value is the most suitable. However, to connect to a network that has
a high bandwidth or to get the highest voice quality, select g711alaw or
g711ulaw from “Codec” command. These values allows better voice quality
but requires more bandwidth for the voice session.
For example, to use a CODEC with G.711a-law Rate for the VoIP dial peer 108,
set the CODEC as follows:
dial-peer voice 108 VoIP
destination-pattern 14085551234
codec g711alaw
session target 10.0.0.8
Besides doing the above, users can create CODEC classes and store them in
- VoiceFinder 1
- [ Contents ] 2
- AddPac Technology Co., Ltd 9
- [ Symbols and Legends ] 11
- Warning 11
- Caution 11
- Information 11
- 1.2. Main Features 14
- Voice over IP Service 15
- IP Routing Protocols 15
- Network Managements 15
- Security Functions 16
- Operation and Managements 16
- Other Scalability Features 16
- 2.1. Unpacking 17
- 3.1. Installation 23
- 3.1.2. Console Connection 24
- ConsoleLAN 0LAN 1 25
- AP1100 VoIP Gateway 25
- Port Configuration Settings 25
- 4.1. Gateway Booting 32
- 4.2. Command Usage 35
- Command Description 38
- Commands Description 39
- Configuration Mode) 44
- 4.4. Ethernet Configuration 46
- 4.4.2. PPPoE Configuration 50
- Operation 51
- 4.5. Routing Configuration 59
- [[Procedure] 64
- [NAT Glossaries] 71
- Order Operation 72
- 순서 작업 내용 Description 82
- Mandatory Commands 82
- Optional Commands 83
- DHCP Type = RELAY 86
- Next Server = 151.1.12.1 86
- 4.10. SNMP Configuration 93
- Sends a message 97
- 4.12.1. Logging Command 105
- 4.12.2. Show commands 106
- File Management 112
- [Procedure] 114
- 4.13.2. Password Recovery 114
- 5.1.1. Voice Over IP 122
- 5.1.2.1. Codecs 123
- 5.1.2.2. Mean Opinion Score 124
- 5.1.3. Dial Peer 126
- 5.1.4. Voice Ports 128
- Configuration 130
- IP Cloud 132
- Destination 132
- Voice Port 145
- Connection 145
- 5.3.4.3. Call barring 146
- Gateway 149
- Step Command Description 155
- 5.7.2.1. dial-peer hunt 172
- 5.7.2.1.5. Example 174
- 5.7.2.2.1. Syntax 174
- 5.7.2.2.2. Default Value 174
- 5.7.2.2.3. Command Mode 174
- 5.7.2.2.4. Usage Guideline 174
- 5.7.2.2.5. Examples 175
- 5.7.2.3.1. Syntax 176
- 5.7.2.3.2. Default Value 176
- 5.7.2.3.3. Command Mode 176
- 5.7.2.3.4. Usage Guideline 176
- 5.7.2.4. dial-peer voice 177
- 5.7.2.5. gateway 178
- 5.7.2.6. num-exp 179
- 5.7.2.6.5. Examples 181
- 5.7.2.7. translation-rule 182
- 5.7.2.8. voice-port 183
- 5.7.2.8.2. Default Value 184
- 5.7.2.8.3. Command Mode 184
- 5.7.2.8.4. Usage Guideline 184
- 5.7.2.8.5. Examples 184
- 5.7.2.9.1. Syntax 185
- 5.7.2.9.2. Default Value 185
- 5.7.2.9.3. Command Mode 185
- 5.7.2.9.4. Usage Guideline 185
- 5.7.2.9.5. Examples 186
- 5.7.2.10.1. Syntax 186
- 5.7.2.10.2. Default Value 186
- 5.7.2.10.3. Command Mode 186
- 5.7.2.10.4. Usage Guideline 187
- 5.7.2.10.5. Examples 187
- 5.7.2.11.1. Syntax 188
- 5.7.2.11.2. Default Value 188
- 5.7.2.11.3. Command Mode 188
- 5.7.2.11.4. Usage Guideline 188
- 5.7.2.12. voice service 189
- 5.7.2.13. VoIP-interface 190
- 5.7.2.13.2. Default Value 191
- 5.7.2.13.3. Command Mode 191
- 5.7.2.13.4. Usage Guideline 191
- 5.7.2.13.5. Examples 191
- 5.7.3.1. comfort-noise 193
- 5.7.3.2. connection 194
- 5.7.3.2.4. Usage Guideline 195
- 5.7.3.2.5. Examples 195
- 5.7.3.3.1. Syntax 195
- 5.7.3.4. echo-cancel 196
- 5.7.3.5. input gain 197
- 5.7.3.5.1. Syntax 198
- 5.7.3.5.2. Default Value 198
- 5.7.3.5.3. Command Mode 198
- 5.7.3.5.4. Usage Guideline 198
- 5.7.3.6. output gain 199
- 5.7.3.7. polarity-inverse 200
- 5.7.3.8. ring number 201
- 5.7.3.8.2. Default Value 202
- 5.7.3.8.3. Command Mode 202
- 5.7.3.8.4. Usage Guideline 202
- 5.7.3.8.5. Examples 202
- 5.7.3.9.1. Syntax 203
- 5.7.3.9.2. Default Value 203
- 5.7.3.9.3. Command Mode 203
- 5.7.3.9.4. Usage Guideline 203
- 5.7.3.9.5. Examples 203
- 5.7.4. Dial Peer Commands 206
- 5.7.4.1. answer-address 206
- 5.7.4.2. codec 207
- 5.7.4.2.2. Default Value 208
- 5.7.4.2.3. Command Mode 208
- 5.7.4.2.4. Usage Guideline 208
- 5.7.4.2.5. Examples 208
- 5.7.4.3.1. Syntax 209
- 5.7.4.3.2. Default Value 209
- 5.7.4.3.3. Command Mode 209
- 5.7.4.3.4. Usage Guideline 209
- 5.7.4.3.5. Examples 209
- 5.7.4.4.1. Syntax 210
- 5.7.4.4.2. Default Value 210
- 5.7.4.4.3. Command Mode 210
- 5.7.4.4.4. Usage Guideline 210
- 5.7.4.4.5. Examples 211
- 5.7.4.5. dtmf-relay 212
- 5.7.4.6. forward-digits 213
- 5.7.4.7. huntstop 215
- 5.7.4.8. port 216
- 5.7.4.9. preference 217
- 5.7.4.10. prefix 218
- 5.7.4.11. register 220
- 5.7.4.11.1. Syntax 221
- 5.7.4.11.2. Default Value 221
- 5.7.4.11.3. Command Mode 221
- 5.7.4.11.4. Usage Guideline 221
- 5.7.4.12. session target 222
- 5.7.4.14. sid 224
- 5.7.4.14.4. Usage Guideline 225
- 5.7.4.14.5. Examples 225
- 5.7.4.15.1. Syntax 225
- 5.7.4.16. vad 226
- 5.7.4.16.1. Syntax 227
- 5.7.4.16.2. Default Value 227
- 5.7.4.16.3. Command Mode 227
- 5.7.4.16.4. Usage Guideline 227
- 5.7.4.16.5. Examples 227
- 5.7.4.17.1. Syntax 228
- 5.7.4.17.2. Default Value 228
- 5.7.4.17.3. Command Mode 228
- 5.7.4.17.4. Usage Guideline 228
- 5.7.4.17.5. Examples 228
- Configuration Command 229
- 5.7.5.1. announcement 229
- 5.7.5.2. codec preference 230
- 5.7.5.3. counter 231
- 5.7.5.4. discovery 232
- 5.7.5.5. fax protocol 233
- 5.7.5.6. fax rate 234
- 5.7.5.6.1. Syntax 235
- 5.7.5.6.2. Default Value 235
- 5.7.5.6.3. Command Mode 235
- 5.7.5.6.4. Usage Guideline 235
- 5.7.5.7. h323 call start 236
- 5.7.5.8. gkip 237
- 5.7.5.9. h323-id 238
- 5.7.5.10. lightweight-irr 239
- 5.7.5.10.1. Syntax 240
- 5.7.5.10.2. Default Value 240
- 5.7.5.10.3. Command Mode 240
- 5.7.5.10.4. Usage Guideline 240
- 5.7.5.10.5. Examples 240
- 5.7.5.11. h323 call channel 241
- 5.7.5.11.5. Examples 242
- 5.7.5.12.1. Syntax 242
- 5.7.5.12.2. Default Value 242
- 5.7.5.13. max-digits 243
- 5.7.5.14. password 244
- 5.7.5.15. public-ip 245
- 5.7.5.16. register 246
- 5.7.5.17. rule 247
- 5.7.5.17.1. Syntax 248
- 5.7.5.17.2. Default Value 248
- 5.7.5.17.3. Command Mode 248
- 5.7.5.17.4. Usage Guideline 248
- 5.7.5.17.5. Examples 249
- 5.7.5.18.1. Syntax 250
- 5.7.5.18.2. Default Value 250
- 5.7.5.18.3. Command Mode 250
- 5.7.5.18.4. Examples 250
- 5.7.5.19.1. Syntax 251
- 5.7.5.19.2. Default Value 251
- 5.7.5.19.3. Command Mode 251
- 5.7.5.19.4. Usage Guideline 251
- 5.7.5.20. timeout 252
- 5.7.5.20.2. Default Value 253
- 5.7.5.20.3. Command Mode 253
- 5.7.5.20.4. Usage Guideline 253
- 5.7.5.20.5. Examples 253
- 5.7.6.1. clear h323 call 256
- 5.7.6.2. clear voice port 257
- 5.7.6.3. show call active 257
- 5.7.6.3.1. Syntax 258
- 5.7.6.3.2. Default Value 258
- 5.7.6.3.3. Command Mode 258
- 5.7.6.3.4. Usage Guideline 258
- 5.7.6.3.5. Examples 258
- 5.7.6.4.1. Syntax 259
- 5.7.6.4.2. Default Value 259
- 5.7.6.4.3. Command Mode 259
- 5.7.6.4.4. Usage Guideline 259
- 5.7.6.4.5. Examples 259
- 5.7.6.7. show dial-peer 261
- 5.7.6.7.4. Usage Guideline 262
- 5.7.6.7.5. Examples 262
- 5.7.6.8.1. Syntax 262
- 5.7.6.8.2. Default Value 262
- 5.7.6.8.3. Command Mode 262
- 5.7.6.10. show gateway 264
- 5.7.6.11. show num-exp 265
- 5.7.6.13. show user-class 266
- 5.7.6.14. show voice port 267
- 5.7.6.16. debug VoIP call 269
- 5.7.6.17. debug VoIP 270
- IP Routing Service 272
- LAN Service 272
- Hardware Specification 274
Relacionado con productos y manuales para Gateways / Controladores AddPac VoiceFinder AP1100
(335 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales